We are proud to introduce production of DIY conversion plates for rotating back Graflex SLR’s. Machined from 6061-T6 aluminum, these allow you to add a Pacemaker Graphic back to your SLR. We are making these in three distinct varieties. The first two are both for 3x4 RB SLR’s; one is centered for 3x4 peelapart polaroid and the other is centered for 4x5 sheet film. (Neither patterns have been tested with the lomograflok back and are not intended for use with it) The third version is for putting a 4x5 Graflok back onto a 4x5 RB SLR. All versions mount to the SLR with the original RB ring. We also offer a Lomograflok centered variant, but please reach out directly if interested in that version.

Each adapter plate will have threaded holes so you can utilize the 5 screw holes in the Graphic back with the new screws included in each kit. There are an additional 4 countersunk holes around the outer edge for the more adept DIY folk to drill and tap their own holes in their Pacemaker Graflok back. (adding a redundancy measure for more reliable hold, though ultimately not necessary)

For the 3x4 variants we will be including an acrylic reducing mask, as the cropped image leaves soft edges without it. We have also gone a few extra steps and will be including laser cut adhesive felting for your original Graflex back, to aid in converting the camera back to original if you ever wish.

Expected ship date is within 1-2 months from order, as all adapter plates are on currently on a made-to-order basis.

The kits will include:
-Adapter Plate, painted with felt installed.
-Screw Hardware
-Acrylic Reducing Mask (ONLY for the 3x4 variants)
-Lasercut Replacement Felt for Graflex back

Note: Not all Graflok backs are built the same. Oddly, the exact placement of holes on your Graflok back may vary from unit to unit. We have designed the adapter plates pattern to fall into a sort of happy in-between that should fit most iterations. These adapter plates are also only tested for fit with Pacemaker era backs, we are not intending these for use with anniversary edition Speed Graphic backs. Again, these have not been tested with and are not intended for use with the lomograflok instax wide back. Recalibrating your cameras top ground glass is REQUIRED.

Camera and Graflok back NOT included.

If you’ve ever tried hunting for this specific screw, you may have learned that even Graflex only refers to it as a “Special Screw” in any service manuals. It indeed is a very special screw, as it has a large diameter head that retains the shutter release lever for a KE-12. (which are an iteration of Pacemaker Speed Graphic designed for military use)

Although this screw was machined specifically for KE-12 cameras, it is the same dimension of screw that is also used for the Anniversary and Pre-Anniversary Speed Graphics. However, on the Anni and Pre-Anni models this screw is not meant to ever be removed and is fixed in placed from the backside. On KE-12’s this screw is meant to be removed, but over time they may become lost or broken.

One order is for one screw. No washers, levers, or other hardware included.

Specific? Yes. Excessive? Possibly.

Machined from stainless steel, these guide pin removal tools are designed to be a convenient and reliable asset for professionals and hobbyists alike. The tip of this tool is designed specifically for Pentax 67 viewfinder guide pins, mirroring the spanner teeth and recessed channel for the pin itself. The handle has milled flat spots to aid in grip and comfort while the business end of the tip reduces in size to allow for visibility.

Average overall length of tool: 85mm
Guide pins are NOT included.

Note: This tool is in a raw machined finish, exact finish may vary. I am not responsible for damage caused to cameras. Viewfinder guide pins require very little torque to seat correctly and can easily be stripped out. Any wrench when used incorrectly could potentially damage paint or hardware.

Sold as pairs only, these custom machined #4-40 x 3/16” machine screws are made to be a direct replacement for missing Front Rise Screws on Graflex Home Portraits cameras.

A pair of these screws are what attaches the main arm of the focusing carriage to the rise/fall lead screw found on either side of the front standard.

These are made ONLY for Graflex Home Portraits. One order is for one pair of screws. Surface finish may vary.

Rangefinder cams for Pacemaker Speed and Crown Graphic Cameras with top mounted rangefinders. These are CNC machined from aluminum and are copies of the original stamped ones that Graflex once sold.

Surface finish and engraving weight may vary.

Sold in pairs (left and right side), these are replacements for the original rear carriage guides in Pacemaker Speed Graphics. This is a component that is quite commonly broken when the camera is closed incorrectly or has been dropped. Installation of these replacements will require removal of the 4 index pins found on the original hardware.

I have faithfully recreated these from brass with some some aesthetic differences related to my exact machine process. The originals were designed to be a sacrificial component, the idea being that they will break before other parts break. The current batch is available in brass with decorative engine turning and sealed with enamel.

These are sold as pairs of carriage guides only (one order will include one left and one right side), no screw or shim hardware will be included. If you are seeking those extra pieces, please reach out via the contact form.

These are replacement door latch screw hardware kits for Pacemaker Speed and Crown Graphic cameras. It’s unfortunately common that these screws loosen up and are inevitably lost. Although it is also common to replace these with off-the-shelf screws and washers, there is a critical and custom machined bushing that is required to hold the latch in place while not clamping directly against it. These critical stepped bushings are machined in-house and the additional screw & washer hardware are included to provide a seamless and accurate replacement regardless of which exact parts you may be missing. The only notable differences between these and the original hardware are these screws are Phillips head and the locking washers are modern circlip style washers.

Each kit includes a pair of #2-56 x 1/4” machine screws, a pair of stepped bushings, a pair of flat washers, and a pair of locking washers. (2 screws, 2 bushings, 2 washers, and 2 locking washers) Neither the full latch, spring, or button are included in these hardware kits. If you are seeking extra accessory components please submit an inquiry through our ‘contact us’ page and we’d be happy to provide a solution.

Sold in pairs. (one order equals one pair of screw hardware)

These are faithful recreations of original ground glass retaining clips as found on various 8x10 studio camera backs such as the Eastman Commercial View. These are machined from aircraft grade aluminum with a ~2.7mm hole. These are fantastic replacements for original cameras, but an even greater asset for anyone building their own wooden camera.

Each order is for one set of four (4) new clips. No screws are included. Original clip photographed for reference.

Want to shoot that 3x4 without going through the hassle of cutting down film? Look no further than this simple plug-and-play 3x4 Graflex to 4x5 Graflok adapter for 3x4 RB cameras. With precision engineering, this adapter was designed to match the native focal plane as close as possible requiring minimal ground glass adjustment and creates an image of just over 4x4.5 ratio. This adapter kit includes the Graflok Base-Plate in landscape orientation with our Spring Viewer set with hand-ground glass to help framing.

As this adapter simply replaces the original camera back, that means it is 100% reversible- preserving your camera for whatever life chooses next.

Let us save you the headache so you can get out there and shoot!

(This mount is intended for Graflok style holders and accessories; Camera, film holder, viewing attachment, film holders, or wood screws not included - Some variation in texture/color may exist between units or parts. Some assembly required on users end)

Please note, all products are currently being made-to-order and can take 2-3 weeks processing/manufacturing time before shipment.